How to Pick the Perfect Dewatering Pump
Basements, yards, and construction sites can all flood, but with the help of a ...
Hover to zoom
1 Of 5
+
Share This Product
Features
Inlet Size
2"
Style
Dewatering
GPM
158 Gallons
Engine
Honda GC
- 2" General Purpose Water Pump
- Designed for clear water removal
- 160cc Honda GC 4-Cycle Engine
- Unsurpassed quality, performance and reliability
- Fast & Reliable Starting
- Automatic mechanical decompression further ensures easy starting
- Aluminum Pump Housing & Cast Iron Impeller
- Extends the life of the pump
- Self-Priming Design
- Requires initial priming to operate
- Includes:
- Strainer & Clamps
- Excellent Consumer Warranty
- 1-Year Pump and 2-Year Honda GC Engine
- EPA Approved & CARB Compliant
California residents see
Warning: This product can expose you to chemicals including Lead which is known to the State of California to cause Developmental Harm.
For more information go to: www.p65Warnings.ca.gov
Specifications
WP-2050HL
Pump
Gallons Per Minute
158 Gallons
Inlet Diameter
2"
Outlet Diameter
2"
Self Priming
Yes
Pump Head Material
Aluminum
Pump Housing Drain
Yes
Quick Clean Out
No
Mechanical Seal Material
Ceramic Carbon
Impeller Material
Cast Iron
Handles Solids
No
Suction Head
26 Feet
Total Head Lift
82 Feet
Submersible
No
Engine
Engine Brand
Honda GC
Starting System
Recoil Start
Engine Cycles
4-Cycle
Low Oil Shutdown
Yes
Fuel Tank Size
0.5 Gallons
Consumer Engine Warranty
2 Years
Commercial Engine Warranty
90 Years
Accessories
Tool Kit
No
Strainer
Yes
Hose Couplings
No
Float Switch
No
Hose
Sold Separately
Hose Bands
Yes
Transport Handle
No
Wheel Kit
No
Overview
Weight
55 Pounds
Consumer Warranty
1 Year
Product Length
20 Inches
Product Width
16 Inches
Product Height
17 Inches
Reviews
(2)
BE WP-2050HL Reviews & Ratings
Product Q&A
(1)
Product Questions
Answered by Jim, the Water Pump Expert
Question
+−
Hi Jim Is it okay to have the input 2 inch in and reduce the output to a 1 1/2? that would probably increase the PSI a little bit more too, right? or do I have to match both input and output with the same size hose? Thank you.
Marc D
from Minnesota
January 22, 2014
Answer
It is always recommended that you use the same diameter hose/piping as the suction and discharge ports on the pump. While it is sometimes necessary to reduce that diameter, it is NOT recommended that you do so by more than one size. In this case, 1-1/2" hose or piping would be the maximum reduction, While you may see an increased pressure due to the reduced piping, the pump will also see an increased backpressure on the pump. The more you reduce the hose/piping diameter, the more you increase this backpressure AND increase premature pump failure that would NOT be covered under warranty.
Was this answer helpful?
Yes
9
No
0
Recommended Accessories
Expert Recommended Accessories
Selected by Jim, our Expert
Required Accessories
9
These accessories are required to properly setup/install this product.
Optional Accessories
10
How-To Articles
What to Do Before, During, and After a Flood
Flooding is scary. It can happen anytime, anywhere, and causes damage without d...
How to Pick the Perfect Gas Water Pump
If you need to know how to move a lot of water FAST, you're reading the right p...
Water Pumps How-To Library
Articles, Tips and Buying Guides from Our Experts
Manuals
Ask A Question!
*Required Fields
+
Thank You For Submitting Your Question
Your submission has been sent successfully. Please give our experts up to two business days to respond.
Media Gallery
BE WP-2050HL - 158 GPM (2") Water Pump w/ Honda GC Engine
Customer Review Images
